Plasma Gouging
Plasma Gouging
Although plasma gouging may use the same gear as plasma cutting, it typically uses a different torch set up and a longer distance between the torch and the metal.Video of the Day
Robotic Plasma Gouging and MIG Welding Cylindrical Stators
Plasma Gouging Items of Interest Max200 High Capacity, Dual Gas Plasma Hand Gouging System With 100' Leads, 600 Volt, 3 Phase, 60 Hz073136 High Capacity...Low Cost Operation...Dual Gas Capabilities: The MAX200 is the Answer to your Heavy Duty Metal Cutting Needs. The MAX200 continues Hypertherm's tradition of combining advanced technology and superior quality to deliver operating advantages that are unmatched in the industry. Features: -200 amp, 30 kw power output delivers heavyduty cutting capacity up to 2 inches (50 mm) thick on most metals; typical cutting speeds greatly exceed oxyfuel or other methods -A state-of-the-art transistorized power supply maintains constant output current regardless of variations in input voltages or torch-to-work distances, ensuring clean, square cuts throughout the cutting range -Adjustable power output from 40 to 200 amps lets the operator precisely match power to cutting requirements -MAX200's dual gas system - plasma and shield - allows you to run on Air/Air, O2/Air, N2/Air, N2/CO2, Ar-H2-N2 or other combinations for optimal results on all metals and in all conditions -The MAX200's patented shielded torch front-end practically eliminates the possibility of double arcing, greatly enhancing piercing capabilities and extending consumable parts life -The MAX200 is available in all common voltages, including 240/480 V, 3 , 60 Hz and 220/380/415 V, 3 , 50/60 Hz configurations -The water-cooled torch provides maximum cooling, another factor behind MAX200's long consumable parts life; the cooling system is built into the power supply for exceptional convenience -A machine motion delay control comes built into every system -A full set of easy-to-read indicator and diagnostic lights monitor the status of external door panels, transformer temperature, coolant level, plasma and shield gas pressure, coolant temperature, and coolant flow, greatly simplifying troubleshooting -MAX200 comes equipped with casters for easy wheeling, and there is a lifting eye located at the balance point for use with cranes -Safety interlocks are built in, ensuring maximum operator safety Benef Max200 High Capacity, Dual Gas Plasma Hand Gouging System With 100' Leads, 208 Volt, 3 Phase, 60 Hz073148 High Capacity...Low Cost Operation...Dual Gas Capabilities: The MAX200 is the Answer to your Heavy Duty Metal Cutting Needs. The MAX200 continues Hypertherm's tradition of combining advanced technology and superior quality to deliver operating advantages that are unmatched in the industry. Features: -200 amp, 30 kw power output delivers heavyduty cutting capacity up to 2 inches (50 mm) thick on most metals; typical cutting speeds greatly exceed oxyfuel or other methods -A state-of-the-art transistorized power supply maintains constant output current regardless of variations in input voltages or torch-to-work distances, ensuring clean, square cuts throughout the cutting range -Adjustable power output from 40 to 200 amps lets the operator precisely match power to cutting requirements -MAX200's dual gas system - plasma and shield - allows you to run on Air/Air, O2/Air, N2/Air, N2/CO2, Ar-H2-N2 or other combinations for optimal results on all metals and in all conditions -The MAX200's patented shielded torch front-end practically eliminates the possibility of double arcing, greatly enhancing piercing capabilities and extending consumable parts life -The MAX200 is available in all common voltages, including 240/480 V, 3 , 60 Hz and 220/380/415 V, 3 , 50/60 Hz configurations -The water-cooled torch provides maximum cooling, another factor behind MAX200's long consumable parts life; the cooling system is built into the power supply for exceptional convenience -A machine motion delay control comes built into every system -A full set of easy-to-read indicator and diagnostic lights monitor the status of external door panels, transformer temperature, coolant level, plasma and shield gas pressure, coolant temperature, and coolant flow, greatly simplifying troubleshooting -MAX200 comes equipped with casters for easy wheeling, and there is a lifting eye located at the balance point for use with cranes -Safety interlocks are built in, ensuring maximum operator safety Benef Max200 High Capacity, Dual Gas Plasma Hand Gouging System With 25' Leads, 240/480 Volt, 3 Phase, 60 Hz073121 High Capacity...Low Cost Operation...Dual Gas Capabilities: The MAX200 is the Answer to your Heavy Duty Metal Cutting Needs. The MAX200 continues Hypertherm's tradition of combining advanced technology and superior quality to deliver operating advantages that are unmatched in the industry. Features: -200 amp, 30 kw power output delivers heavyduty cutting capacity up to 2 inches (50 mm) thick on most metals; typical cutting speeds greatly exceed oxyfuel or other methods -A state-of-the-art transistorized power supply maintains constant output current regardless of variations in input voltages or torch-to-work distances, ensuring clean, square cuts throughout the cutting range -Adjustable power output from 40 to 200 amps lets the operator precisely match power to cutting requirements -MAX200's dual gas system - plasma and shield - allows you to run on Air/Air, O2/Air, N2/Air, N2/CO2, Ar-H2-N2 or other combinations for optimal results on all metals and in all conditions -The MAX200's patented shielded torch front-end practically eliminates the possibility of double arcing, greatly enhancing piercing capabilities and extending consumable parts life -The MAX200 is available in all common voltages, including 240/480 V, 3 , 60 Hz and 220/380/415 V, 3 , 50/60 Hz configurations -The water-cooled torch provides maximum cooling, another factor behind MAX200's long consumable parts life; the cooling system is built into the power supply for exceptional convenience -A machine motion delay control comes built into every system -A full set of easy-to-read indicator and diagnostic lights monitor the status of external door panels, transformer temperature, coolant level, plasma and shield gas pressure, coolant temperature, and coolant flow, greatly simplifying troubleshooting -MAX200 comes equipped with casters for easy wheeling, and there is a lifting eye located at the balance point for use with cranes -Safety interlocks are built in, ensuring maximum operator safety Benef  Thermal Dynamics 9-8225 Gouging Tip A Pkg = 5Thermal Dynamics 9-8225 Gouging Tip A Pkg = 5Part # 9-8225GougingAsimple method of metal removal by angling the torch to a lead angle of35-45 degrees and using a gouging tip. While maintaining a constantstandoff distance, this allows for only a partial penetration into thework, thus removing metal from the surface. The amount of current,travel speed, standoff distance, lead angle and tip size will determinethe amount of material removed and the profile of the gouge. Can usethe Shield Cup Body with either the Gouging Shield Cap or the ShieldDeflector. Can also use the single piece Shield Cup.  Import 120607 Gouging Nozzle 900 NozzleConsumables Suitable for Hypertherm« Type: Gouging Nozzle 900 For Use With: PowerMAX 800® Pac121 Torch, PowerMAX 900® Pac 125 Torch Plasma Gouging Auctions of Interest THERMAL DYNAMICS PLASMA GOUGING shield cap 9-8241 Ends in 8 Days 11 Hours 47 Minutes Current price: $15.37 (8 bids)  plasma cutter,tig,torch,welder,welding,cable,Gougi Ends in 8 Hours 43 Minutes 37 Seconds Current price: $0.89 (0 bids)  Miller Plasma Gouging Tips (8) 138-738 Spectrum $1 Ends in 29 Days 22 Hours 18 Minutes 56 Seconds Current price: $62.00 (0 bids)  TIG torch,welder,Welding,Gouging,welding plug,plas Ends in 9 Hours 23 Minutes 26 Seconds Current price: $0.35 (0 bids)  Hypertherm Plasma Cutter One Gouging Shield 120608 Ends in 17 Days 22 Hours 41 Minutes 1 Seconds Current price: $28.99 (0 bids)  Hypertherm Plasma Cutter One Nozzle Gouging 120831 Ends in 16 Days 21 Hours 59 Minutes 17 Seconds Current price: $18.99 (0 bids)  Thermal Dynamics 9-6502 Plasma Gouging Tip Lot of Ends in 1 Days 1 Hours 44 Minutes 22 Seconds Current price: $20.00 (0 bids)  Hypertherm Plasma Cutter One Nozzle Gouging 120281 Ends in 16 Days 48 Minutes 14 Seconds Current price: $10.99 (0 bids)  Lincoln Plasma Gouging Tips Welding Vortech Nozzle Ends in 4 Days 12 Minutes 25 Seconds Current price: $19.99 (0 bids)  Hypertherm Plasma Cutter One Gouging Nozzle 220059 Ends in 16 Days 4 Minutes 32 Seconds Current price: $17.99 (0 bids) |
